Key takeaways
- Compare the best motorcycle hand grips for comfort on long rides, with anti-vibration picks, gel compounds and sizes for common bar types today.
As an Amazon Associate we earn from qualifying purchases.
Grips are the smallest part of your motorcycle you touch, and the first to tell you something is wrong. Tingling fingers twenty minutes into a commute, palms that ache after an hour on the highway, hands that go cold and clumsy in November — all of it passes through two short sleeves of rubber. A good set of grips will not transform a bike, but the right compound, diameter, and pattern can take the edge off engine buzz, spread pressure across your palm, and keep your hands fresher on long days.
This roundup covers five grips with different jobs: a gel grip for street and dual sport riders, a tri-density off-road grip, a heated grip for cold weather, an isolator-style cruiser grip, and a retro waffle grip for cafe and V-twin builds. Every pick below is a genuine throttle-side pair, matched to specific bar sizes and riding styles.
Disclosure: This article contains affiliate links. If you make a purchase through these links, we may earn a commission at no extra cost to you.
How to Choose
Start with bar diameter, because nothing else matters if the grip does not fit. Most Japanese and European motorcycles use 7/8-inch (22 mm) handlebars. Harley-Davidson models and many cruisers use 1-inch bars. The left grip slides directly onto the bar, while the throttle-side grip is larger inside because it fits over the throttle tube — on a 7/8-inch setup that means roughly a 22 mm hole on the left and a 25 mm hole on the right. A matched pair handles this for you, but you must order the right bar size, and you should measure your bars with calipers if you are unsure. Also check your throttle arrangement: cable throttles, throttle-by-wire housings, and integrated tubes all change what slips on cleanly.
Compounds decide how a grip feels after an hour. Single-density rubber is firm, durable, and honest — it transmits more buzz but lasts for years. Gel grips use a softer layer that deforms under your palm and damps high-frequency vibration, at the expense of quicker wear and slightly vaguer control feel. Dual- and tri-density designs put a firm core against the bar for stability and a soft compound where your hand actually rests, which is why they dominate the off-road world. Pattern matters too: a half-waffle or full-waffle surface gives your fingers something to hook onto in mud and rain, pillow-top pads spread load across the palm, and smooth diamond patterns suit gloved street riding.
Diameter is a comfort lever most riders ignore. A slim grip around 29–30 mm gives precise throttle feel and suits smaller hands. A larger grip, 32 mm and up, spreads pressure over more of your palm and can ease cramping and joint ache on long rides, but it blunts fine throttle control and can tire small hands that have to wrap further around it.
Heated grips are a class of their own. They wire into the bike’s 12-volt system and warm your palms from underneath, which beats piling on thicker glove insulation. Look for a controller with several heat levels and, ideally, a battery-saving mode that cuts power when voltage sags, or wire the kit through a switched feed or relay so a forgotten switch cannot flatten your battery overnight. Check the draw — most quality kits pull under 4 amps — against your charging system’s spare capacity, especially on small-displacement bikes.
Installation is simple but unforgiving of shortcuts. Most old grips come off fastest by slicing them lengthwise with a utility knife, taking care not to score the throttle tube. Clean the bar, then use proper grip glue, hairspray, or compressed air to slide the new grip home depending on the maker’s instructions; off-road riders add safety wire so a wet grip cannot spin. Decide about bar ends before you start — closed-end grips may need trimming to refit bar-end weights, mirrors, or hand guards.
Finally, the honest truth about vibration. Grips work at the contact patch only. They soften the buzz that reaches your palms, but bar-end weights, a properly balanced front tire, healthy engine mounts, and padded gloves each do as much or more. Treat grips as one layer of a system, not a cure for a bike that shakes.
Pro Grip 714 Gel Grips
The Pro Grip 714 Gel Grip is the default upgrade for riders on 7/8-inch bars who want less buzz without changing how the bike feels. Progrip builds the 714 with a harder inner structure and a gel outer layer, so the grip holds its shape on the bar while the surface gives under your palm. At 125 mm long it matches the stock grips on most street, adventure, and dual sport machines — a true like-for-like swap.
This is the grip to pick for parallel twins, singles, and older inline fours that tingle through the bars at cruising rpm. The gel layer takes the sharp edge off that vibration, and the classic raised pattern keeps a gloved hand planted in the wet. It is not a plush touring grip — the diameter stays close to stock, so riders chasing relief from cramping should look at the larger options below — but as an all-round street grip that quietly improves every ride, the 714 has earned its following.
Specs
- Brand: Progrip
- Model: 714BK
- Length: 125 mm
- Bar fit: 7/8 in (22 mm) bars, throttle side sized for the tube
- Material: dual-density rubber with gel layer
- Color: black
Pro Taper Pillow Top Grips
For dirt and dual sport riders, the Pro Taper Pillow Top takes the opposite approach to comfort: instead of gel, it uses a tri-density compound and a surface of raised pillow pads. The firm base resists twisting on the bar, the softer contact layer absorbs trail shock, and the reinforced end — Pro Taper calls it an anti-rip tip — survives the tip-overs that shred ordinary grips.
The pillow pattern is the point. Each raised pad compresses under your fingers and palm, which spreads load and reduces the hand fatigue that builds over a long off-road day, while the flanged design suits twist throttles on standard 7/8-inch off-road bars. Riders who split time between road and trail should know this is a dedicated off-road grip: the flange and aggressive texture feel busy on long highway stretches. Within its intended world of single-track, fire roads, and motocross, it remains one of the most copied designs in the paddock.
Specs
- Brand: Pro Taper
- Model: 024858
- Pattern: pillow top with full flange
- Compound: tri-density
- Bar fit: 7/8 in bars, twist throttle
- Color: black/grey
Oxford Heaterz Premium Cruiser Heated Grips
Cold hands are a control problem, not just a comfort problem, and the Oxford Heaterz Premium Cruiser is built for riders who refuse to park the bike when temperatures drop. This version fits 1-inch handlebars, the size found on Harley-Davidson models and most cruisers. Five heat settings let you match output to conditions, from a gentle take-the-chill-off level in autumn rain to full heat on a frosty morning run.
The details separate it from generic heated grips. The intelligent controller includes a battery-saving mode that switches the grips off if voltage falls to 10.5 volts, protecting a weak battery, and the kit draws less than 4 amps while reaching up to 122 degrees Fahrenheit. Silicone cables stay flexible in deep cold instead of cracking, and the box includes the wiring harness, glue, and cable ties for a straightforward install. The soft, grippy rubber surface is shaped to absorb vibration, which means these work as proper comfort grips even with the heat off.
Specs
- Brand: Oxford
- Fitment: 1 in handlebars (cruiser models)
- Heat settings: 5, up to 122°F
- Draw: under 4 A at 12 V
- Protection: battery-saving cutoff at 10.5 V
- Included: grip pair, controller, wiring harness, glue, cable ties
Kuryakyn 6183 ISO-Grips
Kuryakyn’s ISO design attacks vibration differently: instead of relying on soft rubber alone, it suspends rubber pads in a rigid cover so the pads are isolated from the bar itself. The Kuryakyn 6183 ISO-Grips apply that idea to the Honda Gold Wing, using a clamshell cover that fits over the stock grips of 2006–2019 GL1800 and 2013–2016 F6B models — including bikes with factory heated grips, which most replacement grips force you to give up.
The chrome covers and black pads give the big Wing a finished, custom look, and the recessed channels between pads let air circulate so palms stay drier in summer heat. Because the covers clamp over the existing grips, the finished diameter is substantially larger than stock, which many touring riders with larger hands or stiff joints will welcome: more surface, less squeeze, less cramping on long stints. Fitment is narrow and specific, so confirm your model and year before ordering, and note the removable end caps mean bar-end accessories remain an option.
Specs
- Brand: Kuryakyn
- Model: 6183
- Fitment: Honda GL1800 2006–2019 and F6B 2013–2016, including OEM heated grips
- Design: clamshell covers with isolated rubber ISO pads
- Finish: chrome with black pads
- Weight: about 499 g for the kit
ODI Vans Cult Street Motorcycle Grips
Some grips sell comfort through technology; the ODI Vans Cult grips do it through one of the most proven tread patterns ever made. ODI molds the classic Vans waffle sole into its proprietary rubber compound, and the result is a grip that feels instantly familiar — soft, tacky, and reassuring in any weather. This gum rubber version fits 1-inch bars, making it a natural match for V-twin customs and retro builds, and its medium diameter adds a measure of vibration damping without bulk.
At 125 mm long with a simple slip-on design, installation is the classic cut-off, glue-on routine, and you will need your stock throttle tube or equivalent, since none is included. There is no flange and no high-tech compound story here — just a well-judged rubber, a pattern your fingers read instinctively, and the cafe-racer look that has made these a staple on custom bikes. Riders of 7/8-inch machines should check the matching size in the same line rather than forcing this 1-inch version onto smaller bars.
Specs
- Brand: ODI (Vans/Cult collaboration)
- Pattern: Vans waffle sole
- Length: 125 mm
- Bar fit: 1 in bars; throttle tube required
- Compound: ODI proprietary rubber, gum color
- Sold as: one pair
FAQ
How do I know which grip size fits my motorcycle?
Measure your handlebar’s outside diameter with calipers. Most Japanese and European bikes use 7/8-inch (22 mm) bars; Harley-Davidson and many cruisers use 1-inch bars. The throttle-side grip is always made larger inside to fit over the throttle tube, so a correctly matched pair for your bar size is all you need — but never force a 7/8-inch grip onto a 1-inch bar or ride with a loose 1-inch grip on smaller bars.
Will softer or larger grips stop my hands going numb?
They help, but they are only part of the answer. A softer compound or gel layer damps the high-frequency buzz that causes tingling, and a larger diameter spreads pressure across your palm. If numbness persists, look at bar-end weights, glove padding, your grip pressure and posture, and the bike itself — tire balance and engine mounting among them. Grips are one layer of a system.
Are heated grips difficult to wire?
Most kits need basic 12-volt skills: two ring terminals at the battery, a routed harness, and a mounted controller. The safest setups use a controller with a low-voltage cutoff or draw power from a switched feed or relay, so the grips cannot drain the battery with the engine off. Before fitting, confirm your charging system has spare capacity beyond the kit’s draw, which is typically under 4 amps.
What is the easiest way to remove old grips and fit new ones?
Slice worn grips lengthwise with a utility knife and peel them off, keeping the blade away from the throttle tube. Clean the bar, then slide the new grip on using grip glue, hairspray, or compressed air as the maker directs, and let glue cure fully before riding. Off-road riders often add safety wire at two or three points so a soaked grip can never rotate unexpectedly.
Conclusion
Match the grip to the problem. For everyday street and dual sport comfort on 7/8-inch bars, the Pro Grip 714 Gel is the safest all-round pick. Off-road riders should take the Pro Taper Pillow Top for its tri-density padding and durability. If cold weather ends your season early, the Oxford Heaterz Premium Cruiser adds real, controllable heat for 1-inch bars. Gold Wing tourers who want a larger, isolating grip without losing factory heat should choose the Kuryakyn 6183 ISO-Grips, and retro or V-twin builders after feel and style in equal measure will be happiest with the ODI Vans Cult grips. Whichever you pick, confirm your bar diameter first — the best grip anywhere is useless in the wrong size.
More from Amazon
Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.
Free shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.
Start a Prime free trialA Prime membership for ages 18-24 with a trial period. Eligibility is set by Amazon.
See Prime for Young AdultsAudiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.
Try Audible freeAd-free music streaming. Eligible new subscribers can start with a free trial.
Try Music Unlimited freeAs an Amazon Associate we earn from qualifying purchases.






Write Your Review
No reviews yet. Be the first to share your experience!